Duct-tape Sketchbook Pocket

My working sketchbook goes on adventures with me. Sometimes I’ll end up with ticket stubs or programs from events– and sometimes I’ve got worksheets from class, or doodles friends have given me. I like to keep these items organized chronologically, and stuff them in the back of my sketchbooks, where I’ve built a duct-tape pocket to prevent things from falling out. Now you can make one, too!

Continue reading

Make your own Hanging Zoetrope!

So you’ve always liked animation and you always thought zoetropes were cool. Perhaps you wanted to make your own zoetrope but felt a little lazy and didn’t quite have the motivation to go dig a motor out of some old kid’s toy? Or maybe you never quite knew how to go about it before.
Well, boys and girls, ladies and gentlemen, I now bestow upon you my super-simple, super-cheap, relatively-quick instructions for a zoetrope made out of household goods!

Continue reading

Cheap animation disc desk instructions!

Hey all you animators that just took off for home and plan on working on your films but don’t have fancypants desks that lift up at angles! This one’s for YOU!

animdisc2

animdisc1

I figured I wanted to animate and clean up in comfort, so I scavenged around and found a backing to an 18×24″ Biggie pad that was sitting around, waiting to become useful. I came up with this contraption, which requires no more than said piece of cardboard (non-corrugated, this is really tough stuff!), a box-cutting knife, packing and duct tape (though you could probably get away with just good ol’ duct tape).

animdisc3

  1. Here’s how it works. Take the cardboard and cut strips approximately 2.5″-3″ thick strips down the long way.
  2. On one side of these, make a light cut into both ends, approximately the width of the packing/duct tape you’re working with. Fold the board on these light cuts; now, turn over the board and make a light cut exactly in the middle of the strip. Fold the board back on these new cuts. You should have your strips shaped as you see in the following illustration, by the massive “x2″ (as you’ll make two strips like this, one for the left, and one for the right).
  3. Get your packing tape ready! line up the “feet” of the strips vertically with one of the long edges of the remaining part of the board that you originally cut the strips from. Tape the feet on flat. Now, with the strips bent in an upside-down V, place your disc on them and figure out a distance (with the board pushed to the edge of a table against a wall you plan on working against) that you’re happy with your disc being propped up at. Translation: figure out the angle that you want the strips to be bent at; an angle that you’re comfortable with. Once you’re happy with the angle, make sure the remaining “feet” are about lined up and tape them in place… when you tape the feet, tape them on the front of the board and wrap the tape to the back. (Hence the overhang in the illustration).
  4. Now, get a little sliver of duct tape and fold about half an inch of it over itself and tape it down lined up with the start of the angle of the bent strips. This piece of duct tape will hold your disc in place.

animdiscinstructions

That should be it! You’ll work with the entire “contraption” pushed up against a wall so it doesn’t slip away, though I’m sure you could tape it down to a desk instead. There’s plenty of room for a desk lamp to be used as a backlight as well, which also helps weight down the entire setup.

Improve on it as you wish; this is the first thing that popped into my head and it’s working so far (though I’m only on day 1 with it!) Feel free to post comments and suggestions– I hope the instructions are clear!

New Button Swag!



The Button-Bracelet converter allows you to wear any five 1″ buttons together as a bracelet!


The Button-Earrings converters lets you wear a pair of buttons as earrings!

And here are the latest button releases.


VALUE BLiND Buttons


Companion Cube Buttons… Sorry, you’ll have to settle for these because I couldn’t figure out the engineering behind a Portal gun.

TAHN-EMPORIUM LAUNCHED!

tahnemporium You know you want to buy some hip buttons! Now at tahnee.org’s BrightEye Studios Tahn-Emporium, you can buy buttons to your heart’s content. Buttons are only 95 cents a piece and sell in packs of 5 or more. Shipping’s only 80 cents (FLAT RATE!!) to anywhere in the US!!!!

I Believe! Dont you?

I Believe! Don't you?



Where else will you find 1 Powerstrip buttons?

Where else will you find 1" Powerstrip buttons?

Waka Waka Waka!

Waka Waka Waka!

Feeling Puzzled?

Feeling Puzzled?

Really. Where else are you going to get hot buttons like these? New designs added as often as I can! I’m open to suggestions for any designs you may want to see, so post your ideas!

And a major-shout out to Daniel and the OC community, this would have been impossible without them!